Legend Tuned · ECU Software

Motorcycle

BMW Motorrad R 18 (2020–) R 18 / R 18 Classic 91 HP ECU Yazılımı & Chip Tuning

  • 2020–present
  • Petrol
  • 91 HP · 158 Nm

Target with Legend Tuned Stage 1: 96 HP / 166 Nm; with Stage 2: 101 HP / 172 Nm. The original software is backed up, the calibration is tailored to the car, and the result is verified by datalog.

Legend Tuned figures

Stage 1
Power +5 HP +5%
96 HP Stock 91 HP · 67 → 71 kW
Stock
91 HP
Stage 1
96 HP
Torque +8 Nm +5%
166 Nm Stock 158 Nm
Stock
158 Nm
Stage 1
166 Nm

Figures are examples/estimates and may vary with the car's mileage, maintenance condition, fuel quality and hardware. Exact results are determined by dyno/datalog.

Power & torque curve

Stock vs Stage comparison

A representative power and torque curve with a technical table of all figures. Hover over the chart to see values by rpm.

Technical figures

BMW Motorrad R 18 / R 18 Classic (2020–) 91 HP — stock and Stage figures
Value Stock Stage 1 Stage 2
Power91 HP96 HP101 HP
Power (kW)67 kW71 kW74 kW
Torque158 Nm166 Nm172 Nm
Power gain—+5 HP (+5%)+10 HP (+11%)
Torque gain—+8 Nm (+5%)+14 Nm (+9%)
Vehicle
BMW Motorrad R 18 (2020–)
Type
Motorcycle
Engines
R 18 / R 18 Classic
Years
2020–present
Fuel
Petrol

Figures are examples/estimates and may vary with the car's mileage, maintenance condition, fuel quality and hardware. Exact results are determined by dyno/datalog.

Custom software · 6 options

Custom software options for this engine

Legend Tuned functions suitable for this engine, which can be applied in the same session as Stage software or on their own.

Stage 2 hardware, peace of mind and process

Stage 2 requirements

Stage 2 ready with exhaust and air filter

At Stage 2, the engine's breathing is freed up with hardware: the exhaust and air filter are upgraded, and the software is written to match that hardware. The target for this engine is 101 HP / 172 Nm.

  • Exhaust systemA slip-on or full exhaust system; the software is written for the exhaust fitted.
  • Air filterA high-flow sport air filter; the airbox inlet is modified if needed.
  • Datalog & fine-tuningAir/fuel ratio and ignition are logged during a road or off-road test; fine-tuning is done if needed.
  • Health checkIgnition, fuel system, clutch / CVT belt and cooling checked for this power level; the job takes ~4–8 hours (depending on parts fitted).

Included every time

Power with peace of mind

  • Original software backup — the factory software is read and archived before the job.
  • Reversal — the car can be returned to its original software whenever you ask.
  • Datalog check — ignition, air/fuel ratio and engine temperature are recorded and checked during a road or off-road test.
  • Vehicle-specific calibration — not an off-the-shelf file; tuned to the engine, hardware and fuel quality.
  • Pre-tune diagnostics — fault memory is read and engine health is checked before the software.
  1. Book

    Tell us about your car and your goals; we'll plan the day and time together.

  2. Analysis & backup

    Fault memory is read, the ECU is identified and the original software is archived.

  3. Legend Tuned software

    Calibration tailored to the car (Stage 1: ~1–2 hours).

  4. Test & handover

    Verified with a road test + datalog, then handed over with a walkthrough of what was done.

BMW Motorrad R 18 (2020–)

Other engines in the same generation

All engines table

Vehicle Selector

Choose another vehicle

Start by selecting a make.

Stage 1 96 HP +5
Book an appointment